Intelligent Continuous Feed/Discharge CVD Equipment BTF-1200C-III-3D-CVD-D210
Keywords:
Category:
- 产品对比
- Product Information
- Product Video
- Experimental Case
- Accessories and Consumables
-
Structural Description
· Feed Chamber: The feed chamber’s sealing housing is constructed from a quartz tube, with lateral flanges at both ends for sealing. A 16 mm‑diameter push rod is mounted on the left‑hand flange of the feed chamber, enabling the carrier to be pushed into the high‑temperature furnace under vacuum or inert‑gas protection. The right‑hand flange of the feed chamber is connected to and isolated from the high‑temperature furnace via a pneumatic slide valve, allowing the feed chamber and the tubular high‑temperature furnace to operate independently without mutual interference.
· High-Temperature Growth Furnace: The large-diameter tubular furnace employs high‑quality resistance wire heating, with a maximum operating temperature of 1100°C. Its heating zone measures 300 mm × 300 mm × 300 mm, and it features three‑zone temperature control, each with dual‑point upper and lower temperature regulation, effectively enhancing temperature uniformity. Additionally, the system is equipped with over‑temperature, under‑temperature, and thermocouple‑breakage alarm protection, significantly reducing the reliance on operator experience.
· Discharge chamber: The discharge chamber is enclosed in a sealed housing made of quartz tubing, with lateral flanges at both ends for sealing. A Φ16 mm pull‑rod is mounted on the right‑hand flange of the discharge chamber, enabling the carrier to be drawn from the high‑temperature furnace into the discharge chamber under vacuum or inert‑gas protection for cooling. The left‑hand flange of the discharge chamber is connected to and isolated from the high‑temperature furnace via a pneumatic slide valve, allowing the discharge chamber and the high‑temperature tube furnace to operate independently without mutual interference.
· Sliding mechanism: The left-side sealing flange of the feed chamber is equipped with a push rod and a guide rail; the right-side sealing flange of the discharge chamber is equipped with a pull rod and a guide rail. This configuration enables the carrier to be pushed into or pulled out of the high‑temperature furnace under vacuum or inert‑gas protection.
· Gas supply system: The gas supply system comprises three sections: the feed chamber is equipped with one mass flow meter–based inert gas supply unit; the high‑temperature growth furnace is fitted with one mass flow meter–based inert gas mixing unit; and the discharge chamber is provided with one mass flow meter–based inert gas supply unit, for a total of five mass flow meters.
· Vacuum System: The feed chamber is equipped with one mechanical pump (with a pumping speed of 16 m³/s). 3 /h, model DRV-16), one high‑temperature growth furnace, and one mechanical pump (with a pumping speed of 24 m³/h). 3 /h, model DRV-24), the discharge chamber is equipped with one mechanical pump (mechanical pump pumping speed 16 m³/h). 3 /h, model DRV-16), along with a vacuum gauge, a manual butterfly valve, a bellows, and other connecting components, totaling 3 sets.
· Touchscreen Control System: Equipped with an intuitive touchscreen for automatic control, it offers straightforward parameter settings and operation, with automatic data logging and one-touch functionality.
Main Parameters
· Rated voltage: AC 380V three-phase five-wire incoming switch, 3P 40A, Rated power: 18 KW
· Maximum temperature: 800℃
· Continuous Operating temperature: ≤800℃
· Recommended heating rate: ≤10°C/min
· Heating zone dimensions: 150+300+150 mm
· Heating element: resistance wire
· Thermocouple type: Type K
· Cooling water configuration: Water flow rate ≥ 6 L/min
· Air supply configuration: Cylinder‑driven air, 0.45–0.6 MPa, ≥300 L/min; process gas, 0.1–0.3 MPa.
Temperature control system
· Fuzzy PID Control and Self-Tuning Regulation
· Intelligent 30-segment programmable control
· Features ultra‑gentle operation and open‑circuit alarm functionality.
· Temperature control accuracy: ±1℃
Size &Weight
· Device dimensions: 6150 x 860 x 1900 mm (Length × Width × Height)
· Equipment weight: approximately 850 kg
Warranty period
· One-year warranty, lifetime maintenance.
· Consumable parts such as thermocouples, sealing rings, and furnace tubes are not included.
· Damage caused by human error or by the use of corrosive and acidic gases is not covered under warranty.
Precautions
· The internal air pressure must not exceed 0.02 MPa (gauge pressure).
· Due to the high internal pressure of the gas cylinder, a pressure-reducing valve must be installed when introducing gas into the quartz tube. To ensure safety, it is recommended to use a pressure-reducing valve with a rated pressure below 0.02 MPa.
· For experiments involving sample heating, it is not recommended to operate the system with both the vacuum valve and the inlet valve at the furnace tube flange closed. If it is necessary to close these valves during sample heating, continuously monitor the pressure gauge; if the pressure exceeds 0.02 MPa, immediately open the vent valve to prevent accidents such as rupture of the furnace tube or ejection of the flange.
· Customers are advised against using flammable, explosive, or toxic gases. If such gases are unavoidably required for process reasons, please implement all necessary safety and explosion‑proof measures on your own. Our company shall not be held liable for any issues arising from the use of flammable, explosive, or toxic gases.
-







Consultation Message
Contact Us
Service Hotline:400-0033-603
Sales Hotline:180 1997 0653,180 1997 3217,133 0551 1955
Sales Hotline:0551-65146333
After-sales hotline:0551-65148123
Sales email:besteq@163.com
Company Address: No. 6, Yixiu Road, Feixi County, Hefei City, Anhui Province
Anhui Beiyike Equipment Technology Co., Ltd.
Follow the official account
Research Equipment Consultation
Hubei, Jilin, Shaanxi, Heilongjiang
Tianjin, Liaoning, Henan, Hebei
Shanghai, Sichuan, Chongqing, Inner Mongolia
Xinjiang, Ningxia, Tibet, Qinghai
Foreign Trade Consulting
Sublimation Instrument Consultation
Industrial Equipment Consulting
Jiangsu, Zhejiang, Guangdong, Fujian
Hunan Shanxi Gansu Hainan
Guangxi
Beijing, Tianjin, Liaoning, Henan
Hebei, Shanghai, Sichuan, Chongqing
Inner Mongolia, Xinjiang, Ningxia
Tibet Qinghai
Anhui, Guizhou, Yunnan, Hubei
Jilin, Shaanxi, Heilongjiang, Jiangxi
Shandong
Foreign Trade Consulting
Sublimation Instrument Consultation
Process Consulting
After-sales consultation
Copyright © 2026 Anhui Beiyike Equipment Technology Co., Ltd. All rights reserved.












